DoorHan SWING-5000 Instalační manuál

INSTALLATION MANUAL MOTOR FOR SWING LEAF GATES SWING-3000/5000

COMPONENTS SET № Component Quantity 1 Opener 2 2 Front bracket 2 3 Rear joint 2 4 Rear bracket 2 5 Fixing set 1 6

ASSEMBLY Preliminary checks To ensure trouble-free operation, make sure that the gate (whether existing or yet to be installed) has the following

1.2 - Basic Cable Layout THIS DIAGRAM DETAILS THE BASIC CABLE LAYOUT FOR A PAIR OF MOTORS. THE POWER SUPPLY TO THE CONTROL PANEL SHOULD BE LIVE

1.3 - Low Voltage Cable Layout ALL CAME ACCESSORIES CAN BE WIRED 0.2m STRANDED CABLE (BUGLAR ALARM TYPE). THE TUNED ANTENNA SHOULD BE WIRED WITH

INSTALLATION - To ensure you work in safe conditions, we advise you to install the operator while keeping the door fully closed. - Use all the s

1.5 - Attaching the Rear Bracket THE REAR BRACKET IS EQUIPPED WITH ADDITIONAL HOLES TO MAKE INSTALLATION OF THE GATE MOTOR EASIER, OR TO CHANGE

1.6 - Attaching the Front Bracket WITH THE GATE IN THE FULLY CLOSED POSITION WELD THE FRONT BRACKET TO THE FIXING PLATE THEN ATTACH IT TO THE GA

2.3 - Installing the Motors WITH THE COVERS REMOVED INSTALL THE MOTOR ON THE TWO BRACKETS AND SECURE THE MOTOR WITH THE NUTS AND BOLTS PROVIDED.

2.4 - Adjusting the Open Stop Microswitch MANUALLY RELEASE THE REDUCTION GEAR BY INSERTING THE RELEASE KEY AND TURNING IT 180. MOVE THE GAT

2.5 - Wiring the Motors ENSURE BOTH MOTORS ARE ADEQUATELY EARTHED. Fitting the Control Panel in the Casing Securely fasten the control panel P

Contents INSTALLATION MANUAL...

CONTROL BOARD Technical specifications Power supply 230 V~ ( +6% -10%) - 50 Hz Absorbed power 10 W Motor max. load 800 W Accessories max. lo

Led OP_A TOTALLY OPEN LED Led OP_B LED: LED: OPEN LEAF 1 / CLOSE Led STOP LED LED STOP Led FSWCL LED: LED: CLOSING SAFETY DEVICES Led FSW

Electrical connections IMPORTANT: Before attempting any work on the board (connections, maintenance), always cut off power.

Terminal board J1 - Accessories OPEN A - "Total Opening" command (N.O.): any pulse generator (push-button, detector, etc.) which, by cl

PROGRAMMING Leaf l and 2 force By using microswitches SW1, SW2 and SW3, the force (and thus anticrushing safety) of the operator connected to lea

Function logic The automated system's function logic can be selected with microswitches SW7, SW8, SW9 and SW10. By selecting an automatic lo

- SIMPLE LEARNING: Check if the leaves are closed, and then press F push-button for one second: DL10 LED begins flashing and the leaves begin th

Radio controls encoding Connection of DHRE-2 reciever External receiver DHRE-2 is meant for receiving radio remote control signal with 433 MHz

START UP LED CHECK The table below shows the status of the LEDs in relation to to the status of the inputs. Note the following: Led lighted = clo

TROUBLESHOOTING To avoid being electrocuted, only a professional technician is allowed to touch the wires and components on the main panel. PROB

GENERAL SAFETY INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE • For an efficient and safe automated door, correctly observe the installation proced

NOTES

IMPORTANT! DANGER OF CRUSHING. If the power cable of operator SWING is damaged, it must be replaced by qualified personnel, using a new cable of

Material required for installing the SWING operator and the relevant accessories (if present): Cable 2x0,5 mm2 (emitting photocells, pulse gener

WARNINGS FOR THE INSTALLER ATTENTION! To ensure the safety of people, it is important that you read all the following instructions. Incorrect in

20) The installer shall supply all information concerning manual operation of the system in case of an emergency, and shall hand over to the use

TECHNICAL SPECIFICATIONS Swing-5000 Leaf width, m Leaf weight, kg 2.00 1000 2.50 800 3.00 600 4.00 500 5.00 400 Model Sw

Dimensions 1. Cover 2. Front bracket 3. Rear joint 4. Rear bracket 5. Release unit 6. Worm gear